JB/T 10156-1999 带模滚刀 型式和尺寸

ICs25.100JB中华人民共和国机械行业标准JB/T10156-1999带模滚刀型式和尺寸1999-10-08发布2000-03-01实施国家机械工业局发布JBr10156-1999前言本标准的附录A和附录B都是标准的附录4标准由全国刀其标准化技术委员会提出本标准由成都T具研究所归口。本标准起草单位:哈尔滨第一工具厂、上海工具厂、汉江T具厂、太原工具厂、韶关工具厂、贵阳T具厂本标准主要起草人:董英武、齐秀坤、刘德荣。本标准于1999年10月首次发布中华人民共和国机械行业标准JBrT10156-1999带模滚刀型式和尺寸1范囿本标准规定了带模滚刀的型式和尺寸本标准适用于加节距5080-31.750mm,基本齿廓按加工GBT11616同步带的带模用的带模滚2引用标准下列标准所包含的条文,通过在本标准中引用而构成为本标准的条文。本标准出版时,所示版本均为有效。所有标准都会被修订,使用本标准的各方应探讨使用下列标准最新版本的可能性。GBT6132-1993铣刀和铣刀刀杆的互换尺寸GBT11616-1989同步带尺寸JB/T10158-1999带轮带模滚刀技术条件3要求3.!滚刀用于加T直边齿廓带模。3.2滚刀的型式和尺寸按图1和表1的规定图1国家机械工业局199910-08批准20003-01实施JB/Tio156-1999节距P帮型号槽数ZDm2728031.750XXH3.3滚刀做成单头、右旋,容屑槽为平行于其轴线的直槽。3.4滚刀前角为0°3.5滚刀的轴向齿形尺寸按附录A(标准的附录)的规定,滚刀的计算尺寸按附录B(标准的附录)的规定。3.6键槽的尺寸和偏差应符合GBT6133.7标记示例节距P=12700mm的带模滚刀为:带模滚刀12700JB10156-19993.8其它技术要求按JBT10158-1999。JB10156-1999(标准的附录)滚刀齿形尺寸滚刀的轴向齿形尺寸按图A1和表A1的规定。表A1段加齿数范围0000068091072550130316910212154031270000520000.51280006107942026051.2281.712.1221270001o44000010.5554001490.860.3898128ll1.1726254151.270005661001059730293092630583133112109508013002088000106381004990989806457138481237802610000090.676007691.05160.772114365125600313100013071000.1051.15089731.4883126650.3654000180000000031200016208202189615295270101.9100014000137401651400380022715168753886190002970005143470029318246057642.34421.76974.76919100952533160058500712602519740939248681864007293000341.60740.1240205041.15462.55801.8900087520009165410.174021211134322629419050210000671.16960.0087JBrT10156-199表A1(完)节距加齿数范Aa段CD段EF段00000d154200002241905713279441533138040229000.171300011674200172247500713329540185465263922900034270004180604932529708483098020152|639129000514000081937200929258390995732397227048-340068541004120603062726351163862010.856700022219540260226904127583.5216225100280000322318703951274271414936626228031.19940.0044137070.0057663.9680.385.879952054744063500035850001365340071423620969612815676295526635000716900098349940059452921.71536350759251.166635001075400019363250.1037481472427565695609362222550-200433800033.760401716509273.336787262792300513878025945363038316704862897562544525722261635125092001012.8676001310000000005147100334601480413889444786551121571953000571905637561.3064930028544913904995300143800754940081768×24079623898159221937158000756397013957289435440994199154131.7556-1442287700066591102200772524645210259693262285%60059480319814655132110571944343150014885530680711089629508140034002024.575200264JBT10156-1999附录B(标准的附录)滚刀的计算尺寸按图B1所示,表B1给出滚刀计算尺寸数据图B1表B加匚齿数范围4695233~160342°5848-340740483°08°3°5331.750127.892