-
DB32/T 4783-2024 玻璃纤维增强复合材料筋基坑工程应用技术规程
本文件规定了玻璃纤维增强复合材料筋基坑工程的基本规定、材料、设计与计算、施工以及检测与监测等的要求。
本文件适用于基坑工程结构体系中的临时结构构件，主要包括基坑工程中排桩、地下连续墙、冠梁、腰梁、锚杆、土钉等。...2024-08-24 11:15:01浏览：7
查看 -
GB/T 18369-2022 玻璃纤维无捻粗纱 含2024年第1号修改单
GB/T 18369-2022 玻璃纤维无捻粗纱 含2024年第1号修改单...
2024-05-05 00:15:01浏览：13
查看 -
SJ 21286-2018 印制电路用玻璃纤维布规范 Specification for fabric woven from glass for printed circuit boards
本规范规定了印制电路用电子级(E级)玻璃纤维布(以下简称玻纤布)的性能要求、质量保证规定、交货准备和说明事项等。<br />本规范适用于以电子级玻璃连续纤维纱为原料，经织造和表面化学处理而制成的平纹织物。<br /> ...
2024-02-21 01:00:02浏览：36
查看 -
JC/T 1057-2021 玻璃纤维增强水泥(GRC)外墙板 Glass fibre reinforced cement panel for exterior wall
本文件规定了玻璃纤维增强水泥外墙板的术语和定义、分类和标记、一般性规定、原材料、要求、试验方法、检验规则、标志、运输、贮存和出厂合格证。<br />本文件适用于非承重玻璃纤维增强水泥外墙板。...
2024-01-15 12:48:01浏览：17
查看 -
GB/T 43117-2023 玻璃纤维增强热固性塑料（GRP）管 湿态或干态条件下环蠕变性能的测定 正式版
本文件描述了玻璃纤维增强热固性塑料(GRP)管在湿态(完全浸入水中)或干态条件下环蠕变性能的测试方法。蠕变性能包括蠕变系数和长期蠕变刚度。
本文件适用于通过干态条件下的测试评估和控制原材料的一致性，或通过湿态条件下的测试确定模拟使用条件下的长期蠕变性能。
标准号：GB/T 43117-2023
标准名称：玻璃纤维增强热固性塑料(GRP)管湿态或干态条件下环蠕变性能的测定
英文名称：Glass-reinforced thermosetting plastics(GRP)pipes—Determination of the ring creep properties under wet or dry conditions
发布日期：2023-09-07
实施日期：2024-04-01
引用标准：ISO 3126 ISO 7685 ISO 10928
采用标准：ISO 10468:2018《玻璃纤维增强热固性塑料(GRP)管湿态或干态条件下环蠕变性能的测定》 IDT 等同采用
起草人：杨节标、王磊、王哲、杨德旭、徐崇玉、王宝瑞、宋鹏飞、苏跃辉、许华明、郑莉君、瞿果、丁新静、张小苹
起草单位：北京玻钢院检测中心有限公司、福建路通管业科技股份有限公司、浙江华丰新材料股份有限公司、哈尔滨玻璃钢研究院有限公司、恒润集团有限公司、浙江东方豪博管业有限公司、连云港中复连众复合材料集团有限公司、长沙新世管道有限公司、上海上玻检测有限公司、北京玻璃钢研究设计院有限公司
归口单位：全国纤维增强塑料标准化技术委员会(SAC/TC 39)...2023-12-19 23:12:02浏览：27
查看 -
ASTM D5319-2017 玻璃纤维增强聚酯墙和顶板规格 Standard Specification for Glass-Fiber Reinforced Polyester Wall and Ceiling Panels
1.1 This specification covers the classification, materials of construction, workmanship, physical requirements, and methods of testing glass-fiber-reinforced polyester composite wall and ceiling panels intended for use in light construction and semi-structural applications. 1.2 Supplementary information on chemical resistance, impact resistance, and installation practice are provided in Appendix X1. 1.3 The classification of these composite panels into classes based on relative response to a laboratory test shall not be considered a fire-hazard classification. 1.4 Laboratory flammability tests (Test Methods E84 and D1929) applicable to this specification should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or conditions. However, results may be used as elements of a fire risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use. 1.5 The intent of this specification is to define the class, grade, and general laminate properties of the composite wall and ceiling liner panels in order to ensure a quality product which will perform in the intended application. This specification is not intended to restrict or limit technological changes affecting performance when changes are agreed upon between the purchaser and manufacturer. 1.6 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information only. 1.7 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in Tables and Figures) shall not be considered as requirements of this specification. 1.8 This standard does not purport to address all of the safety co...
2023-09-13 23:00:01浏览：21
查看 -
BS ISO 1887-2014 纺织玻璃纤维 易燃物质含量的测定 Textile glass. Determination of combustible-matter content
...
2023-09-06 04:48:02浏览：30
查看 -
-
GB 51258-2017 玻璃纤维工厂设计标准 Standard for design of fiberglass plant
本标准适用于新建、改建及扩建玻璃纤维工厂的工程设计。...
2023-08-23 09:36:01浏览：25
查看 -
IEC 60317-61-2020 特种绕组线规范--第61部分:温度指数180的聚酯玻璃纤维缠绕树脂或清漆裸或漆包矩形铜线 Specifications for particular types of winding wires – Part 61: Polyester glass-fibre wound, resin or varnish impregnated, bare or enamelled rectangular copper wire, temperature index 18
This part of IEC 60317 specifies the requirements of polyester glass-fibre wound, resin or varnish impregnated bare, grade 1 or grade 2 enamelled rectangular copper winding wires,temperature index 180. The impregnating agent can be, for instance, epoxy, polyester, or polyesterimide resin based.<br />NOTE For this type of wire, the heat shock test is inappropriate and therefore a heat shock temperature cannot be established. Consequently, a class based on the requirements for temperature index and heat shock temperature cannot be specified.<br />The range of nominal conductor dimensions covered by this document is:<br />– width: min. 2,0 mm max. 16,0 mm;<br />– thickness: min. 0,80 mm max. 5,60 mm.<br />The specified combinations of width and thickness as well as the specified width/thickness ratio are according to IEC 60317-0-8....
2023-08-21 13:24:01浏览：25
查看 -
ASTM C1658/C1658M-2019 玻璃纤维毡石膏板规格 Standard Specification for Glass Mat Gypsum Panels
<div class="SectionLevel2"> <p class="subsec1 cdone2"><span class="Head3 cdone">1.1</span> This specification covers the glass mat gypsum panels described in <span class="Body-link1 cdone">1.1.1 – </span><span class="Body-link1 cdone"></span><span class="Body-link1 cdone">1.1.3</span>.</p> <div class="SectionLevel3"> <p class="subsec2 cdone2"><span class="Head4 cdone">1.1.1</span> <span class="Head4Title cdone">Glass mat interior gypsum panel, </span>designed for use on walls, ceilings, or partitions and that affords a surface suitable to receive decoration.</p></div> <div class="SectionLevel3"> <p class="subsec2 cdone2"><span class="Head4 cdone">1.1.2</span> <span class="Head4Title cdone">Glass mat coreboard gypsum panel, and glass mat shaftliner gypsum panel, </span>designed for use as a base in multilayer systems or as gypsum studs or cores in semisolid or solid gypsum board partitions, or in shaftwall assemblies.</p></div> <div class="SectionLevel3"> <p class="subsec2 cdone2"><span class="Head4 cdone">1.1.3</span> <span class="Head4Title cdone">Glass mat water-resistant gypsum panel, </span>designed to be used as a base for the application of ceramic or plastic tile on walls or ceilings. This product is also suitable for decoration. (<span style="font-style:italic;font-weight:normal;" class="overriddenformat">This is distinct from a coated glass mat water-resistant gypsum panel ASTM 1178.</span>)</p></div></div> <div class="SectionLevel2"> <p class="subsec1 cdone2"><span class="Head3 cdone">1.2</span> Specifications applicable to all glass mat gypsum panels are located in Sections <span class="Body-link1 cdone">1 – </span><span class="Body-link1 cdone"></span><span class="Body-link1 cdone"></span><span class="Body-link1 cdone">4</span> and <span class="Body-link1 cdone">8 – </span><span class="Body-link1 cdone"></span><span class="Body-link1 cdone">10</span>. Specifications applicable to specific glass mat...
2023-07-31 17:48:01浏览：26
查看 -
ASTM D5117-2017 实心玻璃纤维增强拉挤棒料染料渗透性试验方法 Standard Test Method for Dye Penetration of Solid Fiberglass Reinforced Pultruded Stock
1.1 This dye-penetrant test method covers a means of evaluating solid fiberglass all-roving reinforced pultruded rod or bar stock for longitudinal wicking. There are generally three mechanisms that promote wicking such as delaminations, longitudinal continuous voids, or the presence of hollow fibers. Any or all of them will be operating at a given time. Note 1: Occasionally the flaws listed above may be detected by this test, but other tests are usually required. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems has the potential to result in nonconformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see 10.3 and 10.6. Note 2: There is no known ISO equivalent to this test method. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee....
2023-07-19 08:48:01浏览：31
查看 -
JC/T 940-2022 玻璃纤维增强水泥（GRC）装饰制品
本文件替代JC/T 940——2004
本文件规定了玻璃纤维增强水泥(GRC)装饰制品的分类和标记、一般规定、原材料、要求、试验方法、检验规则以及标志、堆放、装卸、运输和出厂合格证。
本文件适用于非承重玻璃纤维增强水泥装饰制品。...2023-07-08 14:48:01浏览：28
查看 -
JC/T 2726-2022 玻璃纤维增强水泥（GRC）复合外墙板
本文件规定了玻璃纤维增强水泥（简称 GRC）复合外墙板的术语和定义、分类与标记、一般规定、原材料、要求、试验方法、检验规则以及标志、运输和贮存、产品合格证。
本文件适用于建筑围护结构用非承重复合外墙板。...2023-06-19 14:36:02浏览：30
查看 -
GB/T 36493-2018 玻璃纤维短切原丝流动性的测定 Detemination of the flowability for glass fiber chopped stands
本标准规定了玻璃纤维短切原丝(以下简称短切原丝)流动性的测定方法。<br />本标准适用于长度3.0mm～4.5mm的玻璃纤维短切原丝，其他种类的增强纤维，如碳纤维等也可参照使用。...
2023-05-08 03:36:02浏览：41
查看
